ORAJET 3551RA at Glantz

Glantz acrylic is a cell cast acrylic and has a higher surface hardness. It is resilient, easy to handle and fabricate.


Technical Datasheet 10/19 Page 1 of 2

Description 2.75-mil, high performance calendered PVC film in white with a gloss surface and Rapid Air ® Technology Release Liner 88# PE-coated silicone paper featuring advanced air release technology to facilitate quicker, easier application Adhesive Grey, solvent-based repositionable, permanent adhesive that, with heat, can be removed with little or no adhesive residue for up to four years. Area of Use For medium- to long-term outdoor general signage and vehicle graphics requiring limited conformability

Technical Data

Thickness (without liner and adhesive)


Adhered to steel, no shrinkage in cross direction; In length, <.008” Adhered to aluminum, -58°F to +194°F, no variation

Dimensional Stability (FINAT TM-14)

Temperature Resistance Fire Behavior (DIN 75200) Fire Rating

Adhered to steel, self-extinguishing ASTM E 84-07 Class “A” Adhered to stainless steel: 4.1 lb/in

Adhesive Power (FINAT TM-1, after 24 h, average)

Along: Min. 19 MPa Across: Min. 19 MPa Along: Min. 130% Across: Min. 150%

Tensile Strength (DIN EN ISO 527)

Elongation at Break (DIN EN ISO 527)

Seawaterability (DIN 50 021)

Adhered to aluminum, after 100h/73°F, no variation

Shelf Life (68°F/50% relative humidity)

2 years

Minimum Life Expectancy (based on accepted application procedures on vertical surfaces)

7 years (unprinted)

Minimum Application Temperature


Available Lengths Available Widths

150’ (50-yard) 30”, 50”, 54”, 60”

Recommended Laminates

ORAGUARD ® Series 215, 290, 290GF, 293, 297GF

Print Compatibility Latex, Solvent, Eco-Solvent, UV Curable For best results, utilize ORAFOL ICC profiles available at www.orafolamericas.com and allow solvent-based inks to dry for at least 24 hours (48-72 hours preferred) at 70°F before cutting the graphic to the ink or applying a laminate. Note Surfaces to which the material will be applied must be thoroughly cleaned from dust, grease or any contamination which could affect the adhesion of the material. Freshly lacquered or painted surfaces should be completely cured. The compatibility of selected lacquers and paints should be tested by the user, prior to application of the material. Films with structured surface are naturally more sensitive than the unstructured. Accordingly, these films are to be treated carefully both in processing and in cleaning. Impurities affect the appearance of structured films and require more frequent cleaning. Furthermore the application information published by ORAFOL is to be considered. The batch traceability according to ISO 9001 is possible on the basis of the roll number.

www.nglantz.com | 1.866.645.2689


Technical Datasheet 10/19 Page 2 of 2

IMPORTANT NOTICE All ORAJET ® products are subject to careful quality control throughout the manufacturing process and are warranted to be of merchantable quality and free from manufacturing defects. Published information concerning ORAJET ® products is based upon research which the Company believes to be reliable although such information does not constitute a warranty. Because of the variety of uses of ORAJET ® products and the continuing development of new applications, the purchaser should carefully consider the suitability and performance of the product for each intended use, and the purchaser shall assume all risks regarding such use. All specifications are subject to change without prior notice. WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

ORAFOL Americas – GA 1100 Oracal Parkway Black Creek, GA 31308 Phone: 888.672.2251

ORAFOL Americas – CT 120 Darling Drive Avon, CT 06001 Phone: 800.654.7570 ORAFOL Canada 2831 Bristol Circle Oakville, Ontario L6H 6X5 Phone: 888.727.3374 techsupport-americas@orafol.com – www.orafol.com

Page 1 Page 2

Powered by