Note: All dimensions are subject to the tolerance standards of the aluminum extrusion industry. Profile drawings are illustrative and rounded to the nearest 1/16”.
Flexible Face Preparation / Extrusion Guidelines
Tension Clip and Flexible Face Requirements
Frame Type (Part # - Name)
Clip Line “DEDUCT” from trim size on all (4) four sides.
Clip Placement (on Center)
Tension Tool (Part #)
Face Trim Size “ADD” to overall Height and Width of the assembled frame.
3” 4-1/2”
1-1/2” 1-1/2”
6” 6”
5135 5137
#2065 - Dual Frame #2080 - Front Load Wall Mount Tension Frame #2085 - Tension Frame #2086 - Tension Frame II #2090 - Wall Mount Tension Frame #2092 - Bleed Fascia Frame #2094 - 1-1/2” Fascia Frame #2103 - Flat Bleed Retro Frame w/ Reflector Slot #2104 - Flat Bleed Retro Frame #2105 - Bleed Retro Frame #2107 - Flat Bleed Retro Frame II #2112 - 2” Retro Frame #2142 - Dual Divider #2230 - Flat Bleed Double Face Tension Body #2233 - 6” Flat Bleed Single Face Tension Body
6” 6-1/2” 4-1/2” 6” 3” 6-1/2” 6-1/2” 6” 7” 3” 3” 6-1/2”
1-1/2” 1-1/2” 2-1/4” 1-1/2” 1-1/2” 1-1/2” 1-1/2” 1-1/2” 1-1/2” 1-1/2” 1-1/2” 1-1/2”
5” 5” 5” 5” 6” 5” 5” 5” 5” 6” 5” 5”
5135 5135 5137/5138
5135 5135 5135 5135 5135 5135 5135 5135 5135
13”
1-1/2”
5”
5135
Complete tensioning instructions are available. UL Recognized Component Systems The Underwriters Laboratory file number is E136850 R
Extrusion Guidelines
Size of Sign
Typically limited by the comfort factor for hinging the faces open for service Typically limited to approximately 64 square feet Typically limited by the comfort factor for hinging the faces open for service
Single Face Body . . . . . . . . . . . . Medium Body . . . . . . . . . . . . . . Wide Body . . . . . . . . . . . . . . . . . 1-1/2” Retainer . . . . . . . . . . . . . . 1-1/2” Retainer II . . . . . . . . . . . . Fascia Frames . . . . . . . . . . . . . . .
Typically limited to 32 square feet Typically limited to 60 square feet Typically limited to 6’ in height - unlimited length If the size of the sign is such that hinging open for service is not applicable, SignComp offers the following options:
1) SignComp retro fit extrusions attached to steel framework - Access panels through fabricated cabinet.
2) Service the sign by removing the face - a) Rigid plastic faces - The Dual Frame Cover may be removed to allow the plastic faces to slide to one side. b) Flexible fabric faces - Tension Clips easily release to allow access to the interior of the sign.
Steel Support
Medium Body . . . . . . . . . . . . . . . . . . . . . . . . Wide Body . . . . . . . . . . . . . . . . . . . . . . . . . . . Flat 2 Piece Double Face Body . . . . . . . . . . . . Flat 2 Piece Double Face Medium Body . . . . . Flat Double Face Body . . . . . . . . . . . . . . . . . . Flat Double Face Medium Body . . . . . . . . . . .
Up to a 3” steel support, see page 23 Up to a 6” steel support, see page 23 Up to a 12” steel support, see page 24 Up to a 8” steel support, see page 24 Up to a 6” steel support, see page 24 Up to a 2” steel support, see page 24
Round, square or rectangular supports may be used. Do not exceed recommended max sizes.
Note: SignComp extrusions are engineered and designed to allow for a wide latitude of designs and applications. The fabrication techniques and material selection are at the sole discretion of the individual fabricator.
37
Powered by FlippingBook